Product Description:
S-B2A Automatic Gang Slitter is designed for can body blank cutting and is recommended to link with Automatic Sheet Feeder S-B23B. Sheet is sent to first feeding table, guided by flexible roller guiding bars and is fed into round cutters via one finger. Long strips are support by several swing bars then fall down to second feeding table by gravity. Strips are guided by flexible straight bar and are fed into round cutters via two fingers.
Product Description:
S-B37SA Automatic Scrolled Strip Stacker is to link with Scroll Shear S-B26A(B) for scrolled strips collection. Scrolled strips are carried forward to collection tray by flat belts, then receiving forks gradually lower. When strips are piled up to preset height, forks promptly lower down to a roller table to transfer piled strips on a pallet. (At the same time, four small stoppers extrude out to temporarily support after coming strips), then pallet gradually move forward. Forks lift up immediately for second strip stack collection.
Product Description:
S-B31 Automatic Necker with horizontal design. Can cylinder is carried by a timing screw and a turret. Neck is formed due to guidance from a shaped outer necking die made of tungsten carbide. Proper inner die is to prevent wrinkle. With centralized greasing system and multiple safety devices, easy for maintenance and can size changeover.
Product Description:
S-B43A Automatic Seamer is specially designed for square can closing. Flanged can is fed forward through a belt conveyor and an air cylinder push can into a seaming turret. The turret carry can to first seaming station, lifter plate lift can up to chuck, four seaming rollers undertake first seaming operation. Then, can is transferred to second seaming station for second seaming operation. Ends are separated by a pair of magnetic plates and fed into by a magnetic suction pad.
Product Description:
S-B9B Automatic Strip Feed Press is built for can end or battery jacket stamping. Piled strips are lifted by a set of hydraulic cylinders then suck pads send strip one by one to strip feeding station. (also can link with Automatic Strip Feeder S-B18-2M).Reciprocating feeding bar at feeding station push strip into punch tooling. Formed can end (or battery jacket) is ejected out via. an end kicker(or air blowing) to rear while strip scrap is ejected out by a pressing roller to side.
Product Description:
S-B18C(L,LL) Automatic Double Curling Machine with double curling wheel is designed to inward curl the end fringe on round end. Ends punched by a press are delivered by chutes or conveyors into the curling machine. Two turning curling wheels and two set of fixed curling segment curl the end fringe gradually. Two central support rings are to support the ends while they are being curled so as to avoid deformation. Simple structure, easy for operation and maintenance.
Product Description:
S-D21 Automatic Twist-Off Cap Pre-Curler is designed for the cap fringe inward tiny curl. Cap shells, made by press, are lifted up by an elevator and guided to enter the machine via a chute. Six sets of inner curling rollers enter cap inside and carry caps travel along an arc outer curling mold to slightly curl the cap fringe inward. Curled caps are carried out one by one by a magnetic wheel and guided by a chute to enter knurl forming and lining machine S-D29.
Product Description:
S-B63 Automatic Lining Machine is specially designed for small round end. Curled end is separated by a pair of separating knives at end magazine ;then feeding bars send it to lining station. End is lifted up by a turning chuck. Four sets of electronic gun undertake the lining task to evenly spray compound along the end fringe. With recycleable lubricating system and multiple safety devices, easy for maintenance and can size changeover.
Product Description:
S-B70 Automatic Vertical Can Body Shaper with vertical design is easily linked and work together with automatic double seamer. Can cylinder is carried by a timing screw and a turret, can is lifted up by a lifter plate to let expanding mould enter can inside. Expanding strips are expanded via a pair of cam to press the can wall, to shape the can. With recycleable centralized lubricating system and multiple safety devices, easy for maintenance and can size changeover.
Product Description:
S-B53D Automatic Inside Spray Machine is built for three piece tin can production. One side sealed can bodies are fed into from two top can chutes, carried into two spraying stations by two timing screw and turrets. Two sets of NORDSON spraying guns undertake spraying job on each station; first gun for can wall spraying while second gun for can bottom. Spraying angle can be adjusted easily.
